PKW // ProClip // Brodit others // Acura // MDX 07-10 (USA)

  • Übersicht
  • Datenblatt
  • Einbauanleitung
  • Galerie
  • Fragen
For a larger view please click on the picture

Apple iPad Headrest Mount

Art.No.: b810520
article will be ordered for you
81,50 € incl. VAT, plus Shipping
(Weight: 0.049 kg)
Apple iPad Headrest Mount

Brodit Headrest mount


Brodit Item No: 810520

KUDA Item No: b810520

Brodit EAN Code: 7320288105208

Product info: The choice for you who use your iPad in the back seat of a car. The iPad mount is placed onto a front seat's headrest. The installation is quick and easy, no special tools are required and the interior will not be damaged. You can connect e.g. a charging cable to the iPad when it is in the holder.

The mount is equipped with a tilt swivel. This mean that you can adjust the angle in order to avoid light reflection on the screen. You can easily switch between portrait and landscape mode by turning the holder into desired position. It is easy to put the iPad into place in the holder, and to take it with you when leaving the car.

The headrest mount fits a number of vehicles. Measure the headrest in you vehicle. If the following specifications match your measurements, this product will fit your vehicle:
Minimum inner distance between the headrest bars: 123 mm
Maximum outer distance between the headrest bars: 183 mm

Note: ONLY for the front seat

Category: Vehicles

Placemen: Headrest mount, ONLY for the front seat

Instructions: Please read all of the instructions and look at the pictures before attaching the headrest mount.
1. Remove the two screws in the front side of the headrest mount using the enclosed tool, so you get two parts. Loosen the screw underneath the headrest mount so the face plate can be slided back and forth. Adjust the face plate position and tigten the screw. Place one part of the headrest mount on each side of the headrest. Put back the screws and tighten them until the headrest mount is properly in place. Place the monitor holder onto the face plate so the screw fits in the hole in the tilt swivel. Screw a few turns on the screw, just so the thread starts to pull. Pull the holder toward you and hold it slightly tensed, in the same time tighten the screw so the holder is pulled toward the tilt swivel. Tighten the screw firm at first, then loosen it a bit so the holder is firmly in place, but still can be adjusted.
2. To place the device in the holder: Place the lower part of the device in the holder, then flip/press the upper part forwards so it snaps into place in the holder. To remove the device from the holder: Press upwards on the upper part of the holder, in the same time pull the upper part of the device out from the holder and then lift the device up and out from the holder.
3. Switch between portrait and landscape mode by turning the holder.
4. The headrest mount is in place.


Brodit Headrest mount


Brodit Item No: 810520

KUDA Item No: b810520

Brodit EAN Code: 7320288105208

Product info: The choice for you who use your iPad in the back seat of a car. The iPad mount is placed onto a front seat's headrest. The installation is quick and easy, no special tools are required and the interior will not be damaged. You can connect e.g. a charging cable to the iPad when it is in the holder.

The mount is equipped with a tilt swivel. This mean that you can adjust the angle in order to avoid light reflection on the screen. You can easily switch between portrait and landscape mode by turning the holder into desired position. It is easy to put the iPad into place in the holder, and to take it with you when leaving the car.

The headrest mount fits a number of vehicles. Measure the headrest in you vehicle. If the following specifications match your measurements, this product will fit your vehicle:
Minimum inner distance between the headrest bars: 123 mm
Maximum outer distance between the headrest bars: 183 mm

Note: ONLY for the front seat

Category: Vehicles

Placemen: Headrest mount, ONLY for the front seat

Instructions: Please read all of the instructions and look at the pictures before attaching the headrest mount.
1. Remove the two screws in the front side of the headrest mount using the enclosed tool, so you get two parts. Loosen the screw underneath the headrest mount so the face plate can be slided back and forth. Adjust the face plate position and tigten the screw. Place one part of the headrest mount on each side of the headrest. Put back the screws and tighten them until the headrest mount is properly in place. Place the monitor holder onto the face plate so the screw fits in the hole in the tilt swivel. Screw a few turns on the screw, just so the thread starts to pull. Pull the holder toward you and hold it slightly tensed, in the same time tighten the screw so the holder is pulled toward the tilt swivel. Tighten the screw firm at first, then loosen it a bit so the holder is firmly in place, but still can be adjusted.
2. To place the device in the holder: Place the lower part of the device in the holder, then flip/press the upper part forwards so it snaps into place in the holder. To remove the device from the holder: Press upwards on the upper part of the holder, in the same time pull the upper part of the device out from the holder and then lift the device up and out from the holder.
3. Switch between portrait and landscape mode by turning the holder.
4. The headrest mount is in place.

Apple iPad Headrest Mount

Apple iPad Headrest Mount

Art.No.: b810520
No instructions provided.

Sie haben Fragen zu diesem Artikel?

[?] Questions about this product?